Main content
Course: Exploratorium > Unit 3
Lesson 4: Indicating ElectrolysisIndicating Electrolysis: Complete Activity Guide
Breaking up water isn't hard to do.
[insert hero image here]
Break up water into hydrogen and oxygen gas with a simple electrolysis device, and use an acid-base indicator and a magnet to create groovy swirls of color.
Break up water into hydrogen and oxygen gas with a simple electrolysis device, and use an acid-base indicator and a magnet to create groovy swirls of color.
Tools and Materials
- Two stainless steel screws, each at least 1.5” long (available at your local hardware store)
- Shallow clear glass or plastic container such as a Petri dish
- Epsom salts (available at your local drugstore)
- 9-volt battery
- Rubber bands
- Acid-base indicator such as phenol red, phenolphthalein, bromothymol blue, or cabbage juice indicator (see the Teaching Tips section for instructions on how to make your own)—make sure you’re aware of any safety issues and that you know which colors indicate acid and/or base when using your chosen indicator
- Spoon
Assembly
Wrap one rubber band lengthwise around the battery so that the rubber band lays across both of the battery terminals. Wrap another rubber band lengthwise across the battery so it crosses the first rubber band in a perpendicular fashion.
Slide one stainless steel screw beneath the rubber band and on top of each 9-volt battery terminal. Each screw should be positioned so that its treads is in contact with the terminal. The heads of the screws should point in the same direction and the screws should not touch each other. This is your electrolysis device, and the screws are your electrodes—they’ll be conducting electricity during the experiment.
Fill your Petri dish or shallow container with lukewarm water.
Pour Epsom salt crystals into the water (about a 1/3 teaspoon if you’re using a Petri dish). Stir your solution to help dissolve the salt.
Add some of your chosen acid-base indicator to the salt solution until the solution is colored—you’ll need from a few drops to a few milliliters depending on the concentration of your indicator.
To Do and Notice
Submerge the exposed ends of the screws in the solution. Make sure the battery itself doesn’t get wet! You should be able to rest your electrolysis device on the edge of the container.
What do you notice happening at the submerged ends of each screw? Your screws should begin emitting gas bubbles, and different colors should develop at each electrode.
What's Going On?
Did you see bubbles forming at the screw tips? Did one screw emit more bubbles than the other? Look and see which battery terminal is associated with which volume of bubbles, and which terminal is associated with which indicator color.
The molecular formula for water is H2O, where H stands for the element hydrogen and O stands for the element oxygen. In a glass of water, many of the molecules naturally separate out into hydrogen ions (H+) that are positively charged and hydroxide ions (OH-) that are negatively charged. Your electrolysis device causes reactions that pull apart the water even more.
Since opposite charges attract, the hydrogen ion migrates towards and bubbles from the negative electrode and the oxygen-containing hydroxide ion migrates towards and bubbles from the positive electrode. At the same time, you also create a change in pH, or the amount of acid and base, in local areas around the electrodes.
At the positive electrode, two oxygen atoms get pulled from two hydroxide ions and combine to make oxygen gas (O2). This leaves an abundance of free hydrogen ions, which makes it more acidic at the positive terminal—so your indicator should show an increase of acid at the positive terminal. Likewise, when hydrogen ions combine to make hydrogen gas (H2) at the negative terminal, an abundance of freed hydroxide ions are produced near the negative terminal. Therefore, your indicator should show the production of a base at the negative terminal.
The Epsom salt, also know as magnesium sulfate or MgSO4·7H2O, is dissolved in the water to help your battery break up the water more efficiently. Epsom salt breaks up into ions, and these charged particles help carry the electric current around the solution.
Going Further
Rinse out your Petri dish and then place it on top of a flat magnet. Add a new batch of Epsom salt solution and some indicator to the dish, and then submerge your electrolysis device into the new solution. What do you see happening to the different pools of color at the ends of the electrodes?
The different nodes of color should begin to swirl in opposite directions. This is because a moving electric charge such as an ion also has a magnetic field. The field from the permanent magnet underneath the dish starts to push on the mini-magnet ions and influences how they move.
Experiment Tips
If you’d like to use cabbage juice indicator, it’s easy to make your own. Chop up one small head of purple cabbage. Heat a saucepan of water until boiling, then shut off the heat and add the cabbage. Let it steep for 10 minutes until the liquid turns a deep purple. Strain it and discard the solids. Now your cabbage juice indicator is ready to use in this and many other experiments.
Want to join the conversation?
This article should also mention the dangers and the need for precautions when doing this experiment. DON'T USE TABLE SALT, and DON'T PUT FLAMES NEAR THE EXPERIMENT!
If you use table salt (NaCl), chlorine gas Cl2 will be produced and it is POISONOUS!
And whether or not you use Epsom salts or table salt as the electrolyte in the water, there is water in the experiment. As this article mentions, hydrogen gas (H2) will be generated. Hydrogen gas is FLAMMABLE! So NO FLAMES NEAR THE EXPERIMENT!(6 votes)
I agree! I once put flames near hydrogen as a child and I heard a pop and dropped the test tube and broke it. I remember when I used to use salt in my electrolysis and smell this sickly smell.(3 votes)
does it matter if use bolts instead of screws(3 votes)
No, it doesn't matter. The experiment will still work the same until the bolts are attached to the terminals correctly, and are made of Stainless Steel.(2 votes)
this article confused me(2 votes)
if you just add salt into the red cabbage juice and dip the 9V battery with the screws what happenes does it react as the same?(1 vote)
well, the bolts for the battery are (somewhat) optional.(2 votes)
- Can I use bottled water and nothing else mixed with it.
Cause it already has minerals like Sodium and Magnesium to conduct electricity.(1 vote)
its true that bottled water already has some but the ratio of sodium and magnesium to the water is very little so you still have to add extra.(1 vote)